eddy/STM8_samples
1
0
Fork 0
mirror of https://github.com/eddyem/STM8_samples.git synced 2025-12-06 10:45:12 +03:00
Code Issues Packages Projects Releases Wiki Activity
STM8_samples/blinky/blinky.c
Eddy 7919850a6d copy
2014-03-19 00:38:10 +04:00

236 lines
8.5 KiB
C
Raw Blame History

/*
* blinky.c
*
* Copyright 2014 Edward V. Emelianoff <eddy@sao.ru>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#include "stm8l.h"
#include "interrupts.h"
#include "blinky.h"
/*
* 0 0000
* 1 0001
* 2 0010
* 3 0011
* 4 0100
* 5 0101
* 6 0110
* 7 0111
* 8 1000
* 9 1001
* a 1010
* b 1011
* c 1100
* d 1101
* e 1110
* f 1111
*/
/*
********************* Internal timer (HSI) ********************
* on startup: HSI = 2MHz (16/8)
* HSI divisor: CLK_CKDIVR: bits 4,3: f_{HSI}/2^x; bits2..0: f_{CPU}=f/2^x (page 93)
* CLK_PCKENR1/2 - enable periph clocking (page 94,95) reset value: all enabled
*/
/*
********************* Timer1 ********************
* prescaler: TIM1_PSCRH/L, f = f_{in}/(TIM1_PSCR + 1)
* other registers:
* TIM1_CR1 (page 185): | ARPE | CMS[1:0] | DIR | OPM | URS | UDIS | CEN |
* ARPE - Auto-reload preload enable (for TIM1_ARR)
* CMS[1:0]: Center-aligned mode selection (0 - simple counter up/down)
* DIR: Direction (0 - up, 1 - down)
* OPM: One-pulse mode (1 - opm enabled)
* URS: Update request source (When enabled by the UDIS bit, 1 - interrupt only on counter overflow/underflow)
* UDIS: Update disable (1 - disable update int)
* CEN: Counter enable (1 - enable)
* TIM1_CR2 (page 187): | - | MMS [2:0] | - | COMS | - | CCPS |
* MMS[2:0]: Master mode selection (for ADC or other timers)
* COMS: Capture/compare control update selection
* CCPC: Capture/compare preloaded control
* TIM1_IER (page 191): | BIE | TIE | COMIE | CC4IE | CC3IE | CC2IE | CC1IE | UIE |
* B - break; T - trigger; COM - commutation; CC - comp/capt; U - update <--
* TIM1_SR1 (page 192): similar (but instead of IE -> IF)
* interrupt flags
* TIM1_CNTRH, TIM1_CNTRL - counter value (automatical)
* TIM1_PSCRH, TIM1_PSCRL - prescaler value
* TIM1_ARRH, TIM1_ARRL - auto-reload value (while zero, timer is stopped) (page 206)
*/
/*
********************* External interrupts (page 69) ********************
* EXTI_CR1: | PDIS[1:0] | PCIS[1:0] | PBIS[1:0] | PAIS[1:0] |
* per-port sensivity bits:
* 00: Falling edge and low level
* 01: Rising edge only
* 10: Falling edge only
* 11: Rising and falling edge
* EXTI_CR2: | -reserved[7:3]- | TLIS | PEIS[1:0] |
* TLIS: Top level interrupt sensitivity (0: Falling edge, 1 - Rising)
* PEIS[1:0]: Port E external interrupt sensitivity bits
* after config run enableInterrupts()
* ports:
* 5 lines on Port A: PA[6:2]
* 8 lines on Port B: PB[7:0]
* 8 lines on Port C: PC[7:0]
* 7 lines on Port D: PD[6:0]
* 8 lines on Port E: PE[7:0]
* PD7 is the Top Level Interrupt source (TLI), except for 20-pin packages
* on which the Top Level Interrupt source (TLI) can be available on the
* PC3 pin using an alternate function remapping option bit
*/
/*
********************* GPIO (page 111) ********************
* Px_ODR - Output data register bits
* Px_IDR - Pin input values
* Px_DDR - Data direction bits (1 - output)
* Px_CR1 - DDR=0: 0 - floating, 1 - pull-up input; DDR=1: 0 - pseudo-open-drain, 1 - push-pull output [not for "T"]
* Px_CR2 - DDR=0: 0/1 - EXTI disabled/enabled; DDR=1: 0/1 - 2/10MHz
*
*/
/*
********************* UART ********************
* baud rate: regs UART_BRR1/2 !!!VERY STUPID!!!
* f_{UART} = f_{master} / UART_DIV
* if UART_DIV = 0xABCD then
* UART_BRR1 = UART_DIV[11:4] = 0xBC;
* UART_BRR2 = UART_DIV[15:12|3:0] = 0xAD
* registers
* UART_SR: | TXE | TC | RXNE | IDLE | OR/LHE | NF | FE | PE |
* TXE: Transmit data register empty
* TC: Transmission complete
* RXNE: Read data register not empty
* IDLE: IDLE line detected
* OR: Overrun error / LHE: LIN Header Error (LIN slave mode)
* NF: Noise flag
* FE: Framing error
* PE: Parity error
* UART_DR: data register (when readed returns coming byte, when writed fills output shift register)
* UART_BRR1 / UART_BRR2 - see upper
* UART_CR1: | R8 | T8 | UARTD | M | WAKE | PCEN | PS | PIEN |
* R8, T8 - ninth bit (in 9-bit mode)
* UARTD: UART Disable (for low power consumption)
* M: word length (0 - 8bits, 1 - 9bits)
* WAKE: Wakeup method
* PCEN: Parity control enable
* PS: Parity selection (0 - even)
* PIEN: Parity interrupt enable
* UART_CR2: | TIEN | TCEN | RIEN | ILIEN | TEN | REN | RWU | SBK |
* TIEN: Transmitter interrupt enable
* TCIEN: Transmission complete interrupt enable
* RIEN: Receiver interrupt enable
* ILIEN: IDLE Line interrupt enable
* TEN: Transmitter enable <----------------------------------------
* REN: Receiver enable <----------------------------------------
* RWU: Receiver wakeup
* SBK: Send break
* UART_CR3: | - | LINEN | STOP[1:0] | CLCEN | CPOL | CPHA | LBCL |
* LINEN: LIN mode enable
* STOP: STOP bits
* CLKEN: Clock enable (CLC pin)
* CPOL: Clock polarity
* CPHA: Clock phase
* LBCL: Last bit clock pulse
*/
/*
********************* ADC (page 413) ********************
* ADC_DBxRH / ADC_DRH: 9:2 data bits in left-aligned or 9:8 bits in right-aligned mode
* ADC_DBxRL / ADC_DRL: 1:0 data bits in left-aligned or 7:0 bits in right-aligned mode
* ADC_CSR: | EOC | AWD | EOCIE | AWDIE | CH[3:0] |
* EOC: End of conversion
* AWD: Analog Watchdog flag
* EOCIE: Interrupt enable for EOC
* AWDIE: Analog watchdog interrupt enable
* CH[3:0]: Channel selection bits (0..15)
* ADC_CR1: | - | SPSEL[2:0] | - | - | CONT | ADON |
* SPSEL[2:0]: Prescaler selection
* CONT: Continuous conversion (0 for single)
* ADON: A/D Converter on/off <----------------------------------------
* ADC_CR2: | - | EXTTRIG | EXTSEL[1:0] | ALIGN | - | SCAN | - |
* EXTTRIG: External trigger enable
* EXTSEL[1:0]: External event selection
* ALIGN: Data alignment (1 - right alignment, first read ADC_DRL)
* SCAN: Scan mode enable
* ADC_CR3: | DBUF | OVR | reserved[5:0] |
* DBUF: Data buffer enable (on buffered mode data stored not in ADC_DBhl but in ADC_DBxRhl)
* OVR: Overrun flag
* ADC_TDRH/L - trigger shmidt disable (1 - disable)
*/
unsigned long Global_time = 0L; // global time in ms
char onboard_blink = 1; // == 1 to blink on-board LED
int ADC_value = 500; // value of last ADC measurement
int main() {
unsigned long T = 0L;
unsigned char LedCntr = 0;
// Configure clocking
CLK_CKDIVR = 0; // F_HSI = 16MHz, f_CPU = 16MHz
// Configure pins
PD_DDR = GPIO_PIN3; // PD3 - output, other are inputs
PD_CR1 = GPIO_PIN3|GPIO_PIN5; // PD3 is PPout, PD5 is input with pull-up, PD2 is floating input (for ADC)
PD_CR2 = GPIO_PIN5; // enable interrupts for PD5
PD_ODR = GPIO_PIN3; // turn on LED on PD3
// pin interrupts for PD2&PD5
EXTI_CR1 = 0x80; // PDIS = 10 - falling edge
// 5 LEDs on PC3..PC7
PC_DDR = 0xf8;
PC_CR1 = 0xf8; // PPout
// Configure Timer1
// prescaler = f_{in}/f_{tim1} - 1
// set Timer1 to 1MHz: 1/1 - 1 = 15
TIM1_PSCRH = 0;
TIM1_PSCRL = 15; // LSB should be written last as it updates prescaler
// auto-reload each 1ms: TIM_ARR = 1000 = 0x03E8
TIM1_ARRH = 0x03;
TIM1_ARRL = 0xE8;
// interrupts: update
TIM1_IER = TIM_IER_UIE;
// auto-reload + interrupt on overflow + enable
TIM1_CR1 = TIM_CR1_APRE | TIM_CR1_URS | TIM_CR1_CEN;
// configure ADC
// select PD2[AIN3] & enable interrupt for EOC
ADC_CSR = 0x23;
ADC_TDRL = 0x08; // disable Schmitt triger for AIN3
// right alignment
ADC_CR2 = 0x08; // don't forget: first read ADC_DRL!
// f_{ADC} = f/18 & continuous non-buffered conversion & wake it up
ADC_CR1 = 0x73;
ADC_CR1 = 0x73; // turn on ADC (this needs second write operation)
// enable all interrupts
enableInterrupts();
// Loop
do {
// ADC_value sets half-period in ms
if((Global_time - T > (long)ADC_value) || (T > Global_time)){
T = Global_time;
if(onboard_blink) PD_ODR ^= GPIO_PIN3; // blink on-board LED
PC_ODR = (LedCntr++) << 3;
if(LedCntr == 0x20) LedCntr = 0;
}
//if(!(PD_IDR & 0x20) && T < 650000L) T+= 5000L;
//else if(!(PD_IDR & 0x04) & T > 5000L) T -= 5000L; // PD2
} while(1);
}
Reference in New Issue View Git Blame Copy Permalink