mirror of
https://github.com/eddyem/stm32samples.git
synced 2025-12-06 10:45:11 +03:00
134 lines
4.1 KiB
C
134 lines
4.1 KiB
C
/*
|
|
* hardware_ini.c - functions for HW initialisation
|
|
*
|
|
* Copyright 2014 Edward V. Emelianov <eddy@sao.ru, edward.emelianoff@gmail.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
|
|
* MA 02110-1301, USA.
|
|
*/
|
|
|
|
/*
|
|
* All hardware-dependent initialisation & definition should be placed here
|
|
* and in hardware_ini.h
|
|
*
|
|
*/
|
|
|
|
#include "main.h"
|
|
#include "hardware_ini.h"
|
|
#include <libopencm3/stm32/timer.h>
|
|
|
|
/**
|
|
* Init timer4 channel 4 (beeper)
|
|
*
|
|
void tim4_init(){
|
|
// setup PB9 - push/pull
|
|
gpio_set_mode(GPIO_BANK_TIM4_CH4, GPIO_MODE_OUTPUT_2_MHZ,
|
|
GPIO_CNF_OUTPUT_ALTFN_PUSHPULL, GPIO_TIM4_CH4);
|
|
rcc_periph_clock_enable(RCC_TIM4);
|
|
timer_reset(TIM4);
|
|
// timer have frequency of 1MHz to have ability of period changing with 1us discrete
|
|
// 36MHz of APB1
|
|
timer_set_mode(TIM4, TIM_CR1_CKD_CK_INT, TIM_CR1_CMS_EDGE, TIM_CR1_DIR_UP);
|
|
// 72MHz div 72 = 1MHz
|
|
TIM4_PSC = 71; // prescaler is (div - 1)
|
|
TIM4_ARR = BEEPER_PERIOD - 1;
|
|
TIM4_CCR4 = BEEPER_PERIOD/2; // PWM 50/50%
|
|
TIM4_DIER = TIM_DIER_UIE;
|
|
// PWM_OUT for TIM4_CH4
|
|
TIM4_CCMR2 = TIM_CCMR2_CC4S_OUT | TIM_CCMR2_OC4M_PWM1;
|
|
nvic_enable_irq(NVIC_TIM4_IRQ);
|
|
}
|
|
|
|
uint32_t beeper_counter = 1;
|
|
*/
|
|
/**
|
|
* Run beeper for BEEPER_AMOUNT pulses
|
|
*
|
|
void beep(){
|
|
TIM4_CR1 = 0; // stop timer if it was runned
|
|
beeper_counter = BEEPER_AMOUNT;
|
|
TIM4_SR = 0; // clear all flags
|
|
TIM4_CR1 = TIM_CR1_CEN;
|
|
}
|
|
|
|
void tim4_isr(){
|
|
// No signal
|
|
if(TIM4_SR & TIM_SR_UIF){ // update interrupt
|
|
TIM4_SR = 0;
|
|
if(--beeper_counter == 0){ // done! Turn off timer
|
|
TIM2_CR1 = 0;
|
|
}
|
|
}
|
|
}
|
|
*/
|
|
|
|
/**
|
|
* GPIO initialisaion: clocking + pins setup
|
|
*/
|
|
void GPIO_init(){
|
|
// enable clocking for all ports, APB2 & AFIO (we need AFIO to remap JTAG pins)
|
|
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_IOPAEN |
|
|
RCC_APB2ENR_IOPBEN | RCC_APB2ENR_IOPCEN | RCC_APB2ENR_IOPDEN |
|
|
RCC_APB2ENR_IOPEEN | RCC_APB2ENR_AFIOEN);
|
|
// turn off SWJ/JTAG
|
|
AFIO_MAPR = AFIO_MAPR_SWJ_CFG_JTAG_OFF_SW_OFF;
|
|
/*
|
|
* Setup EXTI on PA4 (PPS input from GPS) - pull down
|
|
* EXTI on PA5 - also pull down (trigger for time measurement)
|
|
*/
|
|
gpio_set_mode(GPIOA, GPIO_MODE_INPUT, GPIO_CNF_INPUT_PULL_UPDOWN, GPIO4 | GPIO5);
|
|
//AFIO_EXTICR2 = 0;
|
|
exti_enable_request(EXTI4 | EXTI5);
|
|
// trigger on rising edge
|
|
exti_set_trigger(EXTI4 | EXTI5, EXTI_TRIGGER_RISING);
|
|
nvic_enable_irq(NVIC_EXTI4_IRQ);
|
|
nvic_enable_irq(NVIC_EXTI9_5_IRQ);
|
|
// LEDS: opendrain output (&turn all OFF)
|
|
gpio_set(LEDS_Y_PORT, LEDS_Y1_PIN | LEDS_Y2_PIN);
|
|
gpio_set_mode(LEDS_Y_PORT, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_OPENDRAIN,
|
|
LEDS_Y1_PIN | LEDS_Y2_PIN);
|
|
gpio_set(LEDS_G_PORT, LEDS_G1_PIN | LEDS_G2_PIN);
|
|
gpio_set_mode(LEDS_G_PORT, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_OPENDRAIN,
|
|
LEDS_G1_PIN | LEDS_G2_PIN);
|
|
gpio_set(LEDS_R_PORT, LEDS_R1_PIN | LEDS_R2_PIN);
|
|
gpio_set_mode(LEDS_R_PORT, GPIO_MODE_OUTPUT_2_MHZ, GPIO_CNF_OUTPUT_OPENDRAIN,
|
|
LEDS_R1_PIN | LEDS_R2_PIN);
|
|
// beeper pin: push-pull
|
|
gpio_set(BEEPER_PORT, BEEPER_PIN);
|
|
gpio_set_mode(BEEPER_PORT, GPIO_MODE_OUTPUT_2_MHZ,
|
|
GPIO_CNF_OUTPUT_PUSHPULL, BEEPER_PIN);
|
|
/*
|
|
// USB_DISC: push-pull
|
|
gpio_set_mode(USB_DISC_PORT, GPIO_MODE_OUTPUT_2_MHZ,
|
|
GPIO_CNF_OUTPUT_PUSHPULL, USB_DISC_PIN);
|
|
// USB_POWER: open drain, externall pull down with R7 (22k)
|
|
gpio_set_mode(USB_POWER_PORT, GPIO_MODE_INPUT,
|
|
GPIO_CNF_INPUT_FLOAT, USB_POWER_PIN);
|
|
*/
|
|
}
|
|
|
|
/**
|
|
* PA5 interrupt - print time at button/switch trigger
|
|
*/
|
|
void exti9_5_isr(){
|
|
if(EXTI_PR & EXTI5){
|
|
if(trigger_ms == DIDNT_TRIGGERED){ // prevent bounce
|
|
trigger_ms = Timer;
|
|
memcpy(&trigger_time, ¤t_time, sizeof(curtime));
|
|
}
|
|
EXTI_PR = EXTI5;
|
|
}
|
|
}
|