/*
 * blinky.c
 *
 * Copyright 2014 Edward V. Emelianoff <eddy@sao.ru>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
 * MA 02110-1301, USA.
 */

#include "stm8l.h"
#include "ports_definition.h"
#include "interrupts.h"
#include "main.h"
#include "stepper.h"

/*
 * 0 0000
 * 1 0001
 * 2 0010
 * 3 0011
 * 4 0100
 * 5 0101
 * 6 0110
 * 7 0111
 * 8 1000
 * 9 1001
 * a 1010
 * b 1011
 * c 1100
 * d 1101
 * e 1110
 * f 1111
 */

unsigned long Global_time = 0L; // global time in ms
U16 paused_val = 500; // interval between LED flashing

U8 UART_rx[UART_BUF_LEN]; // cycle buffer for received data
U8 UART_rx_start_i = 0;   // started index of received data (from which reading starts)
U8 UART_rx_cur_i = 0;     // index of current first byte in rx array (to which data will be written)
U8 UART_is_our = 0;       // ==1 if we get UART
// ATTENTION! to change global variable in PROGRAM memory, it should be CONST!!!
const U8 UART_devNUM = THIS_DEVICE_NUM; // device number, master sais it

/**
 * Send one byte through UART
 * @param byte - data to send
 */
void UART_send_byte(U8 byte){
	if(!UART_is_our) return; // don't use UART when we have no right!
	//UART2_CR2 |= UART_CR2_TEN; // enable transmitter
	UART2_DR = byte;
	while(!(UART2_SR & UART_SR_TC));
	//UART2_CR2 &= ~UART_CR2_TEN; // disable transmitter
}

void uart_write(char *str){
	if(!UART_is_our) return; // don't use UART when we have no right!
	//UART2_CR2 |= UART_CR2_TEN; // enable transmitter
	while(*str){
		UART2_DR = *str++;
		while(!(UART2_SR & UART_SR_TC));
	}
	//UART2_CR2 &= ~UART_CR2_TEN; // disable transmitter
}


/**
 * Read one byte from Rx buffer
 * @param byte - where to store readed data
 * @return 1 in case of non-empty buffer
 */
U8 UART_read_byte(U8 *byte){
	if(UART_rx_start_i == UART_rx_cur_i) // buffer is empty
		return 0;
	*byte = UART_rx[UART_rx_start_i++];
	check_UART_pointer(UART_rx_start_i);
	return 1;
}

void printUint(U8 *val, U8 len){
	unsigned long Number = 0;
	U8 i = len;
	char ch;
	U8 decimal_buff[12]; // max len of U32 == 10 + \n + \0
	if(len > 4 || len == 3 || len == 0) return;
	for(i = 0; i < 12; i++)
		decimal_buff[i] = 0;
	decimal_buff[10] = '\n';
	ch = 9;
	switch(len){
		case 1:
			Number = *((U8*)val);
			break;
		case 2:
			Number = *((U16*)val);
		break;
		case 4:
			Number = *((unsigned long*)val);
		break;
	}
	do{
		i = Number % 10L;
		decimal_buff[ch--] = i + '0';
		Number /= 10L;
	}while(Number && ch > -1);
	uart_write((char*)&decimal_buff[ch+1]);
}
/*
U8 U8toHEX(U8 val){
	val &= 0x0f;
	if(val < 10) val += '0';
	else val += 'a' - 10;
	return val;
}

void printUintHEX(U8 *val, U8 len){
	U8 i, V;
	uart_write("0x");
	for(i = 0; i < len; i++){
		V = *val++;
		UART_send_byte(U8toHEX(V>>4)); // MSB
		UART_send_byte(U8toHEX(V));    // LSB
	}
	UART_send_byte('\n');
}*/

U8 readInt(int *val){
	unsigned long T = Global_time;
	unsigned long R = 0;
	int readed;
	U8 sign = 0, rb, ret = 0, bad = 0;
	do{
		if(!UART_read_byte(&rb)) continue;
		if(rb == '-' && R == 0){ // negative number
			sign = 1;
			continue;
		}
		if(rb < '0' || rb > '9') break; // number ends with any non-digit symbol that will be omitted
		ret = 1; // there's at least one digit
		R = R * 10L + rb - '0';
		if(R > 0x7fff){ // bad value
			R = 0;
			bad = 0;
		}
	}while(Global_time - T < 10000); // wait no longer than 10s
	if(bad || !ret) return 0;
	readed = (int) R;
	if(sign) readed *= -1;
	*val = readed;
	return 1;
}

void error_msg(char *msg){
	uart_write("\nERROR: ");
	uart_write(msg);
	UART_send_byte('\n');
}

/**
 * read motor number
 * @param N - readed Number
 * @return 0 in case of error
 */
U8 get_motor_number(U8 *N){
	int Ival;
	if(readInt(&Ival) && Ival > -1 && Ival < 3){
		*N = (U8) Ival;
		UART_send_byte('*'); // OK
		return 1;
	}else{
		error_msg("bad motor");
		return 0;
	}
}

void show_uid(){
	uart_write("\nMCU ID:\n");
	printUintHEX(U_ID00, 12);
}

/**
 * Change variable stored in program memory
 * !!! You can change only const values (non-constants are initializes on program start)
 * @param addr - variable address
 * @param new value
 * @return 0 in case of error
 */
U8 change_progmem_value(U8 *addr, U8 val){
	// unlock memory
	FLASH_PUKR = EEPROM_KEY2;
	FLASH_PUKR = EEPROM_KEY1;
	// check bit PUL=1 in FLASH_IAPSR
	if(!FLASH_IAPSR & 0x02)
		return 0;
	*addr = val;
	// clear PUL to lock write
	FLASH_IAPSR &= ~0x02;
	return 1;
}

/*
U8 change_eeprom_value(U8 *addr, U8 val){
	// unlock memory
	FLASH_DUKR = EEPROM_KEY1;
	FLASH_DUKR = EEPROM_KEY2;
	// check bit DUL=1 in FLASH_IAPSR
	if(!FLASH_IAPSR & 0x08)
		return 0;
	*addr = val;
	// clear DUL to lock write
	FLASH_IAPSR &= ~0x08;
	return 1;
}
*/

int main() {
	unsigned long T = 0L;
	int Ival;
	U8 rb, Num;

	CFG_GCR |= 1; // disable SWIM

	// Configure clocking
	CLK_CKDIVR = 0; // F_HSI = 16MHz, f_CPU = 16MHz

	// Timer 4 (8 bit) used as system tick timer
	// prescaler == 128 (2^7), Tfreq = 125kHz
	// period = 1ms, so ARR = 125
	TIM4_PSCR = 7;
	TIM4_ARR = 125;
	// interrupts: update
	TIM4_IER = TIM_IER_UIE;
	// auto-reload + interrupt on overflow + enable
	TIM4_CR1 = TIM_CR1_APRE | TIM_CR1_URS | TIM_CR1_CEN;

	// Configure pins
	// PC2 - PP output (on-board LED)
	PORT(LED_PORT, DDR) |= LED_PIN;
	PORT(LED_PORT, CR1) |= LED_PIN;
	// PD5 - UART2_TX -- pseudo open-drain output; don't forget an pullup resistor!
	PORT(UART_PORT, DDR) |= UART_TX_PIN;
	PORT(UART_PORT, ODR) |= UART_TX_PIN; // torn off N push-down
	//PORT(UART_PORT, CR1) |= UART_TX_PIN;

	// Configure UART
	// 9 bit, no parity, 1 stop (UART_CR3 = 0 - reset value)
	// 57600 on 16MHz: BRR1=0x11, BRR2=0x06
	UART2_BRR1 = 0x11; UART2_BRR2 = 0x06;
	UART2_CR1  = UART_CR1_M; // M = 1 -- 9bits
	UART2_CR2  = UART_CR2_REN | UART_CR2_RIEN; // Allow RX, generate ints on rx

	setup_stepper_pins();


	// enable all interrupts
	enableInterrupts();
	// Loop
	do{
		if((Global_time - T > paused_val) || (T > Global_time)){
			T = Global_time;
			PORT(LED_PORT, ODR) ^= LED_PIN; // blink on-board LED
		}
		if(UART_read_byte(&rb)){ // buffer isn't empty
			switch(rb){
				case 'h': // help
				case 'H':
					uart_write("\nPROTO:\n"
						"+/-\tLED period\n"
						"Ex/ex\tset/get end-switches stored\n"
						"p\tget HW end-switches\n"
						"Mx\tstop on end-switch\n"
						"Sx/sx\tset/get Mspeed\n"
						"mx\tget steps\n"
						"Px\tpause/resume\n"
						"Xx\tstop\n"
						"0..2N\tmove xth motor for N steps\n"
						"=\tinfinity moving (after 0..2)"
						"U/u\tset/get U-stepping\n"
						"I\tget serial ID\n"
						"N\tchange HW number\n"
						"n\tshow HW number\n"
						);
				break;
				case 'I': // get serial id
					show_uid();
				break;
				case '+':
					paused_val += 100;
					if(paused_val > 10000)
						paused_val = 500; // but not more than 10s
				break;
				case '-':
					paused_val -= 100;
					if(paused_val < 100)  // but not less than 0.1s
						paused_val = 500;
				break;
				case 'E': // set end-switches value
					if(get_motor_number(&Num)){
						if(readInt(&Ival) && (Ival == (Ival & 0x1f))){
							if(Num)
								EPs[Num] = Ival & 0x0f; // 4 bits in motors 1&2
							else
								EPs[0] = Ival; // all 5 bits in motor 0
						}else
							error_msg("bad EP");
					}
				break;
				case 'e': // get stored end-switches value
					if(get_motor_number(&Num)){
						printUint(&EPs[Num], 1);
					}
				break;
				case 'p': // get hardware end-switches value
					if(get_motor_number(&Num)){
						Num = get_ep_value(Num);
						printUint(&Num, 1);
					}
				break;
				case 'S': // set stepper speed
					if(get_motor_number(&Num)){
						if(readInt(&Ival) && Ival > MIN_STEP_LENGTH)
							set_stepper_speed(Num, Ival);
						else
							error_msg("bad speed");
					}
				break;
				case 's': // get stepper speed
					if(get_motor_number(&Num))
						printUint((U8*)&Stepper_speed[Num], 2);
				break;
				case 'M': // move till EP, you can call it before starting motor
					if(get_motor_number(&Num))
						Stop_on_EP[Num] = 1;
				break;
				case 'm': // how much steps there is to the end of moving
					if(get_motor_number(&Num))
						printUint((U8*)&Nsteps[Num], 2);
				break;
				case 'X': // stop
					if(get_motor_number(&Num))
						stop_motor(Num);
				break;
				case 'P': // pause/resume
					if(get_motor_number(&Num))
						pause_resume(Num);
				break;
				case 'N':
					if(readInt(&Ival) && Ival > 0 && Ival < 256)
						if(!change_progmem_value(&UART_devNUM, (unsigned int) Ival))
							error_msg("can't change val");
				break;
				case 'n': // show HW num
					printUint(&UART_devNUM, 1);
				break;
				case 'u': // show UStepping
					printUint(&USteps, 1);
				break;
				case 'U': // set UStepping
					if(readInt(&Ival) && Ival > 0 && Ival < 256)
						USteps = Ival;
				break;
				case '=': // infinity moving: just don't decrement steps
					StepperInfty = 1;
				break;
				default:
					if(rb >= '0' && rb <= '2'){ // run motor
						Num = rb - '0';
						if(readInt(&Ival) && Ival)
							move_motor(Num, Ival);
						else{
							error_msg("bad Nsteps");
						}
					}
			}
		}
	}while(1);
}