diff --git a/with_opencm3/cdcacm.c b/with_opencm3/cdcacm.c
index c2c32fa..5cccba1 100644
--- a/with_opencm3/cdcacm.c
+++ b/with_opencm3/cdcacm.c
@@ -195,9 +195,9 @@ static int cdcacm_control_request(usbd_device *usbd_dev, struct usb_setup_data *
 
 	switch (req->bRequest) {
 	case SET_CONTROL_LINE_STATE:{
-//P("SET_CONTROL_LINE_STATE\r\n", uart1_send);
-//print_int(req->wValue, uart1_send);
-//newline(uart1_send);
+P("SET_CONTROL_LINE_STATE\r\n", uart1_send);
+print_int(req->wValue, uart1_send);
+newline(uart1_send);
 		if(req->wValue){ // terminal is opened
 			USB_connected = 1;
 			//P("\r\n\tUSB connected!\r\n", uart1_send);
@@ -222,11 +222,11 @@ static int cdcacm_control_request(usbd_device *usbd_dev, struct usb_setup_data *
 		usbd_ep_write_packet(usbd_dev, 0x83, local_buf, 10);
 	}break;
 	case SET_LINE_CODING:
-//P("SET_LINE_CODING, len=", uart1_send);
+P("SET_LINE_CODING, len=", uart1_send);
 		if (!len || (*len != sizeof(struct usb_cdc_line_coding)))
 			return 0;
-//print_int(*len, uart1_send);
-//newline(uart1_send);
+print_int(*len, uart1_send);
+newline(uart1_send);
 		memcpy((void *)&lc, (void *)*buf, *len);
 		// Mark & Space parity don't support by hardware, check it
 		if(lc.bParityType == USB_CDC_MARK_PARITY || lc.bParityType == USB_CDC_SPACE_PARITY){
@@ -240,10 +240,10 @@ static int cdcacm_control_request(usbd_device *usbd_dev, struct usb_setup_data *
 		if(len && *len == sizeof(struct usb_cdc_line_coding))
 			memcpy((void *)*buf, (void *)&linecoding, sizeof(struct usb_cdc_line_coding));
 		//usbd_ep_write_packet(usbd_dev, 0x83, (char*)&linecoding, sizeof(linecoding));
-//P("GET_LINE_CODING\r\n", uart1_send);
+P("GET_LINE_CODING\r\n", uart1_send);
 	break;
 	default:
-//P("UNKNOWN\r\n", uart1_send);
+P("UNKNOWN\r\n", uart1_send);
 		return 0;
 	}
 	return 1;
diff --git a/with_opencm3/hardware_ini.c b/with_opencm3/hardware_ini.c
index f3d03e8..d36d520 100644
--- a/with_opencm3/hardware_ini.c
+++ b/with_opencm3/hardware_ini.c
@@ -22,6 +22,8 @@
 #include "main.h"
 #include "hardware_ini.h"
 
+volatile uint16_t ADC_value; // ADC DMA value
+
 /**
  * GPIO initialisaion: clocking + ports setup
  */
@@ -38,4 +40,54 @@ void SysTick_init(){
 	systick_counter_enable();
 }
 
+void ADC_init(){
+	rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC1EN); // enable clocking
+	rcc_periph_clock_enable(RCC_ADC1);
+	rcc_set_adcpre(RCC_CFGR_ADCPRE_PCLK2_DIV4);
+	rcc_periph_clock_enable(RCC_GPIOB); // clocking for ADC port
+	gpio_set_mode(GPIOB, GPIO_MODE_INPUT, GPIO_CNF_INPUT_ANALOG, GPIO0); // ADC8 - PB0
+	// Make sure the ADC doesn't run during config
+	adc_off(ADC1);
+
+	// first configure DMA1 Channel1 (ADC1)
+	rcc_periph_clock_enable(RCC_DMA1); // RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
+	dma_channel_reset(DMA1, DMA_CHANNEL1); //DMA_DeInit(DMA1_Channel1);
+	dma_set_peripheral_address(DMA1, DMA_CHANNEL1, (uint32_t) &(ADC_DR(ADC1))); // DMA_InitStructure.DMA_PeripheralBaseAddr = ADC1_DR_Address;
+	dma_set_memory_address(DMA1, DMA_CHANNEL1, (uint32_t)&ADC_value); // DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)&ADC_value;
+	dma_set_number_of_data(DMA1, DMA_CHANNEL1, 1); // DMA_InitStructure.DMA_BufferSize = 1;
+	dma_set_read_from_peripheral(DMA1, DMA_CHANNEL1); // DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
+	dma_disable_memory_increment_mode(DMA1, DMA_CHANNEL1); // DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Disable;
+	dma_disable_peripheral_increment_mode(DMA1, DMA_CHANNEL1); // DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
+	dma_set_peripheral_size(DMA1, DMA_CHANNEL1, DMA_CCR_PSIZE_16BIT); // DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
+	dma_set_memory_size(DMA1, DMA_CHANNEL1, DMA_CCR_MSIZE_16BIT); // DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
+	dma_enable_circular_mode(DMA1, DMA_CHANNEL1); // DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
+	dma_set_priority(DMA1, DMA_CHANNEL1, DMA_CCR_PL_HIGH); // DMA_InitStructure.DMA_Priority = DMA_Priority_High;
+	dma_enable_channel(DMA1, DMA_CHANNEL1); // DMA_Cmd(DMA1_Channel1, ENABLE);
+
+	// Configure ADC as continuous scan mode with DMA
+	adc_set_dual_mode(ADC_CR1_DUALMOD_IND); // ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
+	adc_enable_scan_mode(ADC1); // ADC_InitStructure.ADC_ScanConvMode = ENABLE;
+	adc_set_continuous_conversion_mode(ADC1); // ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
+	adc_disable_external_trigger_regular(ADC1); // ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
+	adc_set_right_aligned(ADC1); // ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
+	//adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_239DOT5CYC); // ADC_SampleTime_239Cycles5
+	adc_set_sample_time(ADC1, ADC_CHANNEL8, ADC_SMPR_SMP_239DOT5CYC); // ADC_RegularChannelConfig(ADC1, ADC_Channel_8, 1, ADC_SampleTime_239Cycles5);
+	adc_enable_dma(ADC1); // ADC_DMACmd(ADC1, ENABLE);
+	adc_power_on(ADC1); // ADC_Cmd(ADC1, ENABLE);
+}
+
+/**
+ * Starts ADC calibration & after it runs ADC in continuous conversion mode
+ * First call ADC_init(), than wait a little and call this function
+ */
+void ADC_calibrate_and_start(){
+	uint8_t channel_array[16];
+	// adc_set_regular_sequence 1 channel -- 0 // ADC_InitStructure.ADC_NbrOfChannel = 1;
+	channel_array[0] = ADC_CHANNEL8;
+	adc_set_regular_sequence(ADC1, 1, channel_array);
+	adc_reset_calibration(ADC1);
+	adc_calibration(ADC1);
+	adc_start_conversion_regular(ADC1); // ADC_SoftwareStartConvCmd(ADC1, ENABLE);
+	adc_start_conversion_direct(ADC1);
+}
 
diff --git a/with_opencm3/hardware_ini.h b/with_opencm3/hardware_ini.h
index 3578585..d1ecc09 100644
--- a/with_opencm3/hardware_ini.h
+++ b/with_opencm3/hardware_ini.h
@@ -23,7 +23,11 @@
 #ifndef __HARDWARE_INI_H__
 #define __HARDWARE_INI_H__
 
+extern volatile uint16_t ADC_value; // ADC DMA value
+
 void GPIO_init();
 void SysTick_init();
+void ADC_init();
+void ADC_calibrate_and_start();
 
 #endif // __HARDWARE_INI_H__
diff --git a/with_opencm3/ircontroller.bin b/with_opencm3/ircontroller.bin
index ae457dc..4975fe6 100755
Binary files a/with_opencm3/ircontroller.bin and b/with_opencm3/ircontroller.bin differ
diff --git a/with_opencm3/main.c b/with_opencm3/main.c
index c01d445..bae601c 100644
--- a/with_opencm3/main.c
+++ b/with_opencm3/main.c
@@ -46,13 +46,17 @@ int main(){
 	// USB
 	usbd_dev = USB_init();
 
+	// init ADC
+	ADC_init();
+
+	// SysTick is a system timer with 1mc period
+	SysTick_init();
+
 	// wait a little and then turn on USB pullup
 	for (i = 0; i < 0x800000; i++)
 		__asm__("nop");
 	gpio_clear(GPIOC, GPIO11);
-
-	// SysTick is a system timer with 1mc period
-	SysTick_init();
+	ADC_calibrate_and_start();
 
 	while(1){
 		usbd_poll(usbd_dev);
diff --git a/with_opencm3/main.h b/with_opencm3/main.h
index 18086cd..89f9019 100644
--- a/with_opencm3/main.h
+++ b/with_opencm3/main.h
@@ -33,6 +33,8 @@
 #include <libopencm3/usb/usbd.h>
 #include <libopencm3/cm3/systick.h>
 #include <libopencm3/stm32/rcc.h>
+#include <libopencm3/stm32/adc.h>
+#include <libopencm3/stm32/dma.h>
 
 #include "user_proto.h"
 
diff --git a/with_opencm3/user_proto.c b/with_opencm3/user_proto.c
index 14b89a4..5946133 100644
--- a/with_opencm3/user_proto.c
+++ b/with_opencm3/user_proto.c
@@ -22,6 +22,7 @@
 #include "cdcacm.h"
 #include "main.h"
 #include "uart.h"
+#include "hardware_ini.h"
 
 // integer value given by user
 static volatile int32_t User_value = 0;
@@ -60,6 +61,12 @@ void parce_incoming_buf(char *buf, int len, sendfun s){
 		command = buf[i];
 		if(!command) continue; // omit zero
 		switch (command){
+			case 'A': // show ADC value
+				//adc_start_conversion_direct(ADC1);
+				P("\r\n ADC value: ", s);
+				print_int(ADC_value, s);
+				newline(s);
+			break;
 			case 'b': // turn LED off
 				gpio_set(GPIOC, GPIO12);
 			break;